If you are located outside of the United States, or if Section 17 does not apply to you or is otherwise unenforceable as adjudicated by a court of competent jurisdiction, then Section 18 applies to you:. Any action arising out of or relating to this Agreement may be brought exclusively in the appropriate state or federal court in Los Angeles, California, and Belkin and you irrevocably consent to the jurisdiction of such courts and venue in Los Angeles, California.
However, if you are a consumer and you live in a country where Belkin markets or distributes the Software, local law may require that certain consumer protection laws of your country of residence apply to some sections of this Agreement.
In addition, Belkin may seek injunctive relief in any court having jurisdiction to protect its intellectual property rights. Third-party trademarks mentioned are the property of their respective owners. See more languages. Setting up the Belkin router without using the Setup CD. Share the Article:. Step 1: Connect your computer to the modem using an ethernet cable without the router installed. NOTE: Make sure that the modem is plugged into a power source.
Step 2: Verify if your computer is getting an internet connection by accessing a website. Step 2: Plug in your modem and then your router to the power source. If you are using a wireless computer, you will need to connect it first with an ethernet cable. Step 4: Observe the light of your router located at the upper panel of the device.
Wait for a few minutes until the light turns solid blue. If the light does not turn blue or blinking amber, the following is a list of troubleshooting tips that you can perform: Make sure that the router is properly connected to your modem with an ethernet cable.
Powercycle the modem by unplugging it from the power source for a few seconds then plugging it back to the power source again. Powercycle the router by unplugging the router's power supply for 10 seconds then plug it back in. This will help the router to re-establish communication with the modem. Step 1: Open a web browser and enter NOTE: If you are having issues in accessing The router will then establish and test the connection, and then it will check for firmware updates.
Or, if you have previously installed the Belkin utility, uninstall it or right-click on the Belkin icon in the system tray and uncheck Automatic Firmware Update. Step 3: Once the connection has been established, you will be prompted to modify your Network Name and Password. These can be found at the bottom of the router.
If you choose to change your Network Name and Password, fill in the spaces provided for your entry. Step 4: The router will then verify your Network Name and Password.
Once done, click. Step 5: Fill in the necessary information on the Register your router window and click Complete Registration. Step 6: Click the Thanks, take me to the dashboard button. Was this support article useful? YES NO. Thank you for your feedback. Feedback Please tell us how we can make this article useful.
If you are located in the United States, Section 17 applies to you: If you are located outside of the United States, or if Section 17 does not apply to you or is otherwise unenforceable as adjudicated by a court of competent jurisdiction, then Section 18 applies to you: All rights reserved. Additional Support Questions? Search Again. Technical Support. This Agreement constitutes the entire agreement between Belkin and you with respect to the Software and your use thereof and supersedes any conflicting or additional terms contained in any purchase order or elsewhere.
No provision of this Agreement may be waived, modified or superseded except by a written instrument accepted by Belkin and you. However, the Belkin Privacy Policy referenced herein is subject to change in the manner described in that document. Belkin may provide translations of this Agreement as a convenience to users. However, in the event of a conflict or inconsistency between the English and any non-English versions, the English version of this Agreement shall govern, to the extent not prohibited by local law in your jurisdiction.
Any suppliers of Belkin shall be direct and intended third-party beneficiaries of this Agreement, including without limitation with respect to the disclaimers of warranties and limitations on liability set forth herein. Other than as set forth in the preceding sentence, a person or entity who is not a party to this Agreement shall not have any right to enforce any term of this Agreement. No failure or delay in exercising any right or remedy shall operate as a waiver of any such or any other right or remedy.
The language of this Agreement shall not be construed strictly for or against either party, regardless of who drafted such language or was principally responsible for drafting it. The rights and obligations under this Agreement are not assignable by you, and any attempted assignment shall be void and without effect. This Agreement shall bind and inure to the benefit of the parties and their successors and permitted assigns. If you are located outside of the United States, or if Section 17 does not apply to you or is otherwise unenforceable as adjudicated by a court of competent jurisdiction, then Section 18 applies to you:.
Any action arising out of or relating to this Agreement may be brought exclusively in the appropriate state or federal court in Los Angeles, California, and Belkin and you irrevocably consent to the jurisdiction of such courts and venue in Los Angeles, California.
However, if you are a consumer and you live in a country where Belkin markets or distributes the Software, local law may require that certain consumer protection laws of your country of residence apply to some sections of this Agreement. In addition, Belkin may seek injunctive relief in any court having jurisdiction to protect its intellectual property rights.
Third-party trademarks mentioned are the property of their respective owners. See more languages. Share the Article:. T hey can be set up without using cables and wires. The steps below will guide you on how to set up your range extender wirelessly.
Before you begin, ensure that you have the following:. A Wi-Fi-capable device e. NOTE: Details on the troubleshooting steps and images may vary depending on the wireless devices you are using. Step 1: Plug in your range extender into a power outlet that is within the range of your router's wireless network.
Step 2: Using your Wi-Fi-capable device, locate and connect to the Belkin. NOTE: If you are unable to see this network, you may need to reset the range extender. To do this, simply press the range extender's reset button for at least 10 seconds while it is turned ON. Power cycle the range extender then connect to the network again. Wait for your device to connect to the Belkin. Step 4: On the page that opens, tap on Get Started.
It will search for your router's SSID. Step 5: Select the wireless network you want to extend. Tap Next once done. Wait for the setup to connect to the network. Step 6: When prompted, enter your wireless network's password then tap Next.
Wait for the setup to authenticate your password. Step 7: If you have a dual-band network, select the second wireless network you want to extend then repeat Step 6. Step 8: Review the Extended Network information.
Tap Edit if the information needs to be changed. Otherwise, tap the Create Extended Network button to proceed with the setup. Setting up the extenders is not a difficult thing if all the steps are followed properly. But before starting up the setup, you need to make sure that you have the below-mentioned things available with you. Once you have arranged and noted down all the required information, then you can proceed with the steps of the Belkin WiFi Range extender.
Step 4: In case, you are not finding the Belkin. Step 7: The window will open for assisting setup. Click on the Get Started button. Step If you are using the dual-band range extender, then follow from step 8 to step 14 again. Step Click on the Edit button if you want to change something for the network settings.
0コメント