On the explorer, select the file which will be used as profile icon ; extension:. PRO Press Load. Once loaded, the display goes back automatically to Setup screen. Select the profile just loaded. Removing a profile 1 2 In the Profile list, select the profile to be deleted. Press Remove key. Freeze mode Once the image is acceptable, you may freeze the picture. This feature allows to store in memory the resulting picture.
Freezing a scope result does not store the picture in a file see "File menu" page The result will be lost if the instrument is shut off, or if more than 3 pictures are frozen see "Mosaic Mode" page The High Mag.
This function is also available pressing the button directly on the Pi see Figure 22 on page Use the focus control to adjust the focus of the image Launching a test of the connector and fiber end-face Launching a test of the connector and fiber end-face Once the display is correctly adjusted magnification, sharpness To launch the test: 1 Press Test key to launch the test of plugged fiber connector.
It surrounds the majority of the fiber cladding. Zone C: represents the Epoxy ring. In Mosaic mode see "Mosaic Mode" page 56 , the result of the test only displays Pass or Fail information; the status of each zone is displayed only in full screen mode. Overlay The Overlay key allows, when selected, to display the limits of each zone and to display with colors the defaults on the image. When the key is unselected, the zones and defaults are not graphically identified. Use the key Full scr.
The selected picture is framed in green. Once this key is pressed, the freeze image is automatically set on Position 2. Freeze Overlay If all positions were taken, the picture that was once at the fourth position is unloaded from memory. Frozen pictures are lost, unless they were saved on the internal memory. Allows to switch all the images from high to low magnification and vice-versa. This key is not available with jpg files other than those resulting from scope application.
Picture selected: Image Save Allows to save the selected picture in the directory Scope, in the disk of the Platofrm. Press Save key, enter a name for the jpg file and validate.
This key does not work on jpg image which do not result from scope application. Comment Overlay High mag. This comment appears at the bottom left of the picture. The right bottom of the frozen picture also contains the date of the acquisition where the picture was frozen. NOTE Both the comment and the date will be saved with the picture.
Loading a picture It is possible to retrieve and load a picture stored in the Scope directory and display it in the Scope page. Select Load. Some pictures resulting from the Scope option may appear nevertheless unrecognized, if they have been stored with a different Scope application, or if the JPG file has been opened and modified under another JPG editor. That picture is enlarged or shrunk to the size of the display full screen or mosaic, see. On the edition keypad, enter the name of the jpg file Press Enter to validate.
The file is automatically saved on the disk, in the directory Scope icon. Generating a report 1 2 3 Check the correct test result is selected framed in green in mosaic mode. The report generation is completed once the icon displayed on the upper banner. In the File Explorer, select the pdf report just created. The file opens automatically in the PDF viewer. The PDF Reader opens but without document. Interacting with a PDF document Once your document is open, you may browse through different pages very quickly, zoom to a particular level, rotate the page All these features are available via buttons on the screen.
In the Application screen, activate Web Browser icon The web browser is launched. Click on the softkey Mouse so that it becomes. If none keyboard is available, click on Keyboard the virtual keyboard and enter the address: to display b click directly on characters if the platform is equipped with a touchscreen.
The page opens If an error message is displayed in place of the internet page, verify the address you typed, or check the Web configuration see "Configuring the Web access" page Creating Once the internet page for which a bookmark must be created is opened: bookmarks 1 Click on to open the dialog box for bookmarks creation. New toolbar is available on the right of the screen. Click on Ok to confirm the modification or Cancel to cancel the modifications.
Once loading is completed, click on Ok to open the pdf file. Leaving the web browser Depending on how long you want to leave the web browser and on your connection mode, you may: — Leave the web browser running and switch to another task.
For an intensive use of the deport screen or when it is used via a WAN network, it is strongly recommended to use a dedicated VNC client.
Permanent Mode Permanent with password same function as the Permanent mode, with an access to the equipment via VNC protected by a password: The password to access VNC can be modified: 1 2 3 Click on the menu key Change password.
Enter the current password in the Edition keypad and press Enter to validate. Enter the new password and press Enter to validate. If this parameter is selected, the following parameters must be entered: the user can enter the name of the site in the Edit menu. Config 1 to 4 static mode enabling input of the configuration of 4 sites. If Manual has been selected, enter the Proxy Address.
Considering When two or more users are using remote screen function onto the same Platform, the icon is. Virtual control buttons bar It is possible to emulate hard keys with Virtual Control buttons. To display those buttons, click once on the top of the screen in the status bar, at the same height than the date and time.
The Export function is available onto the Platform pressing simultaneously the left and right arrow keys. Validate the File Explorer icon. The File Explorer page appears. The list of files the directory contains displays on the right side The selected directory is underlined in blue 2 Press validation hard key Access to sub-directory , to display the sub-directories if any.
Selected directory Sub-directory Fig. Select and validate the first file of the list underlined in red Set the cursor on the last file of the list underlined in blue Maintain the right direction key selected. Click on Paste menu key. The Edition keypad displays. Click on Enter to validate the new name. A confirmation dialog box displays. Press Yes to delete the selected directory or file s.
Press No to cancel the deletion. Press the right menu key Create Directory. The edition keypad displays Enter a name for this directory Press Enter key to validate the new directory Opening files Once a file is selected, press Load, then Confirm Load menu keys.
Several FO files of the same type example: all otdr cannot be opened at the same time using the Explorer function of the Application page; only the last one selected will open. It can be opened exclusively if the corresponding module is set and activated and if File explorer is opened using the FILE button of the Platform. If different types of files have been selected in the Explorer, only the last one selected will open. CD extension AP file. AP extension ODM file.
HTML extension Text file. TXT extension License file. Sorting files If at least one file is selected, the key Sort allows to access to a submenu allowing to sort the files according to pre-defined parameters: — Sort by name: the files display in an ascending order from A to Z.
If you click once again on the key, the files display in a descending order from Z to A. Sort by size: by clicking once on this key, the files display from the smallest to the heaviest one. Clicking a second time allows to sort the files in opposite order. By clicking again on key, the Platform displays files from the older to the more recent one. Ethernet cable Fig. Double click on Network Connection. Double click on Local Area Connection. In the dialog box, click on Properties.
On the tab General, check the parameter Obtain an IP address automatically is selected ; if not, click to select it. IP Address of the Platform Fig. Accessing the FTP access is obtained through the user account «mts» password: internal memory of acterna. E, Mozilla Firefox In the address bar, type the following address Choose Ethernet if you wish to use the sending mail function.
Auto or Manual. In Auto mode, you will not have the possibility to reply to the mail sent. In Manual mode, the reply will be sent to the address entered in the line From. Use the button to enter into an edition window. Relay Mode Auto or Manual. In Auto mode, the sending of e-mail is performed automatically. Subject: enter the subject of the mail or a comment if necessary.
Click on any key to follow. Configuring the parameters of screenshots To configure the screenshot and choose the format of the generated file: 1 2 On the Home page, press System Settings key to reach the System Settings page. Therefore, if you make a zoom on the trace for example, the file will only show the zoom section. Taking a screenshot Once the screenshot parameters are configured: 1 2 3 Reach the display which will be saved as a screenshot in a file. If necessary, make modifications on this display example: zoom on trace Press simultaneously left and right direction keys or Click on the upper banner of the screen, and click on Print in the control buttons bar displayed for few seconds.
The icon 4 displays until the end of process. For other page open and used for a screenshot, the file is saved in the directory Print, into the disk. Configuring the report To configure the report and choose the format of the report file: 1 2 On the Home page, press System Settings key to reach the System Settings page. In the Printer box, on the line Printer, select File Formatted. To display a Logo on the upper right of the report pages, click on Logo line and select the Logo to be displayed on the upper right of the page: a b c Press Press to open the edition keypad to validate.
Set the trace view as wished. This view is only available with OTDR traces. The icon displays until the end of process. Free space on selected media is clearly displayed at the bottom of the left panel.
One of these can be used to connect an external storage medium, in particular a USB memory stick. Then, the icon is displayed in the upper banner to inform the user the USB stick is ready to be used.
When a file is moved in the explorer of the Platform, the end of the move on the screen does not mean that writing of data into the memory is complete. Some data may still be in a writing process if the storage unit is removed prematurely. USB memory stick 1 Before disconnecting the USB memory stick, always select a storage device different from usbflash select disk for example in disconnection the explorer.
The icon becomes to indicate it can be removed safely. The files stored in bluetooth-inbox are lost when the Platform is switched off. According to the connection type used, specific requirements are mandatory. This application is just saved on PC. Once download is completed, the internet explorer can be closed. Open the directory into which has been save the zip file and unzip files into a directory Open the directory and double click on SmartAccessAnywhere.
Press OK to hide the message. On the distant PC 1 On the PC of the distant user, once the application is launched, enter the Access Number on the upper part of the screen. Transferring files To work on files onto PC and onto unit : 1 On the Introduction page, click on or On the left menu, click on. Once transfer is completed, the banner disappears and the transferred file is underlined in blue on Platform explorer.
Transferring files 1 On the PC explorer, select the storage media, and if wished the sub- directory into which file will be transferred. A dialog box open, allowing to modify the location on PC of the file. Press Save to start the transfer Under both file explorers, a new banner displays with information on file transfer see Figure 66 on page Once transfer is completed, the banner disappears and the transferred file is underlined in blue on PC explorer.
Click on. In the new dialog box opened, press Yes to confirm the deletion or No to keep the file. Creating a new directory 1 2 3 4 Select the storage and, if wished, the directory into which the new directory will be stored. In the new dialog box opened, enter a name for the new directory newdir is given by default. Press OK to validate.
The new directory is automatically created at the location selected. Connection information and settings Displaying session information At any time during application use, the information about the session in progress can be displayed. Modifying connection settings To modify the settings for connection to internet: 1 2 3 Press Session menu key on left of the screen Disconnect from application pressing.
On the session screen see Figure 67 on page , press button. The Internet proxy configuration is available exclusively if the port selected is Alternative port and if the HTTPS packing is selected. It is recommended to configure parameters of connection with your local network administrator, if the default parameters need to be modified.
The Home page displays see Figure 63 on page Testing connection Before entering the Access code to activate the application, the connection to internet can be tested from displayed screen.
Press if wished. If the parameter is defined to Disable, the WIFI application is deactivated, and the icon is no more displayed on the upper banner. Wait for the list of SSIDs to be displayed. Press Select menu key to validated the connection. The display goes back to Setup screen. The SSID parameter is automatically configured with the one selected. Note IP Address Fig. Select the mode of connection: static mode enabling input of the configuration of 4 sites.
If this parameter is selected, the following parameters are available: the user can enter the name of the site in the Edit menu. It is an option that must be installed at the factory. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. A screen as the following one displays: Fig. CDI testing. Datacom Testing with the Multi-Services.
With an intuitive, menu-driven test methodology, the FIREBERD performs traditional bit error analysis, frame and cell generation , along with signal, performance and timing measurements. Vacuum Interrupters Diphase Interface Module. Viavi Solutions. Manual Variable Attenuator. IMUX Intelligent E1 Multiplexer.
With Digital Access Cross Connect. RFL Electronics Inc. January 1, i. Any reproduction or distribution of this manual, Fireberd as the synchronous data sink. Multifuel Models and PureWood Models. Easy to use for novices yet fully featured for experts. Optical Test Platform without Supported applications of the FB include verifying end-to-end circuit continuity and throughput, stressing and verifying clock recovery circuits, and verifying quality of service QoS.
Requires Application Module Sold Separately. Options available at additional cost on request. Similar Products. Add to Cart. Contact Info Please let us know how we can contact you. Additional Info Please let us know any information that will help us fill your requirement such as urgency, quantity needed, etc. In-Stock Notification Request Sent Your request to be notified when this product is back in stock has been sent to our sales department. We will notify you as soon as this item is available for purchase.
Thank you for allowing us the opportunity to assist with your test equipment needs. We hope to earn your business.
Close Wizard.
0コメント